417-862-4455
Differential Covers
GM Dodge Ford Dana 70 Rear Differential Cover 2500 3500 F250 F350
This is a genuine Dana/Spicer cover for the Dana 70 rear differential found in many common domestic trucks. It is also stamped with the part number 42815-2.
View Details
This is a bare open differential for a Dana 60 axle with 4:56 or lower gears (4:88, 5:13, etc.). This is 30,32, or 35 spline axles. This can be used in a front or rear differential. This case comes with a set of ring gear bolts, roll pin for the cross shaft, a set of [...]
View Details
Miscellaneous
This is a genuine Dana/Spicer baffle that goes between the yoke and the outer bearing in a Dana 80 rear differential. This is 1.60″ I.D. and .032″ thick.
View Details
Axles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View Details
Differential Covers
The cover itself is a 43600-1 Stamped steel cover includes 10 bolts and fill plug 1981 – 1988 Chevy Dana 60 Front or Rear 1988 – 1998 Ford F350 Dana 60 front
View Details
Ring & Pinion Sets
This is a genuine Dana/Spicer ring & pinion in a 4:56 ratio that shows to fit trucks with the Super 70/273 axle.
View Details
This is a genuine Dana/Spicer greasable universal joint is a 1410 series. This is the same as 5-1410X except it is greasable.
View Details
This is a genuine Dana/Spicer inner spindle nut for 1990-1997 Ford Rangers with either a Dana 28 or Dana 35 front axle. This is for trucks with manual locking hubs. This is the inner nut with the pin. These are 1.625-16 TPI.
View Details
Cases & Spiders
Internal Differential Kit 27 Spline Jeep JK Wrangler Dana 30 Front 2007-2015 Spider Gear
This is a genuine Dana/Spicer internal or spider gear kit for the Dana 30 4X4 front differential found in 2007-2015 Jeep JK’s. This is for the non-Rubicon Jeep’s.
View Details
This is a genuine Dana/Spicer universal joint for the Dana 30 or 44 front axle found in many 2007 and newer Jeep JK and JL Rubicon and non-Rubicon’s.
View Details
Ring & Pinion Sets
Jeep 2018+ JL/JT Dana 44 Rear Axle 5:13 Ring & Pinion Gear Set Gladiator Wrangler Unlimited Rubicon
This is a genuine Dana/Spicer ring and pinion in a 5:13 ratio, for the Dana 44 rear axle found in most 2018 and newer Jeep JL and JT vehicles.
View Details
Ring & Pinion Sets
Jeep 2018+ JL/JT Dana 44/M220 Rear Axle 3:73 Ring & Pinion Gear Set Gladiator Wrangler Unlimited
This is a genuine Dana/Spicer ring and pinion in a 3:73 ratio, for the Dana 44 or M220 rear axle found in many 2018 and newer Jeep JL and JT vehicles. This replaces Jeep part number 68401362AA.
View Details
Axles & Axle Bearings
Jeep Dana 30 4X4 Front Outer Axle Stub 1987-1991 Wrangler Chromoly
– 27 spline – 6.11″ long – Fits Dana Spicer 30 in Jeeps – Outer stub – 5-260X U-joint size – Chromoly USED IN 1987 TO 1988 AND 1990-1991 The original part number (40611) has been discontinued.
View Details
Cases & Spiders
This is a genuine Dana Spicer bare differential carrier for the Dana 30 4X4 front axle found in many Jeep applications from 1984-2006. This include Wrangler, Cherokee, and Grand Cherokee, XJ, YJ, and TJ. This is for 3:54 and faster gear ratio’s (3:08 etc.).
View Details
For Use In 1987-06 Wrangler 1984-01 XJ Cherokee 1986-92 MJ Comanche 1993-98 ZJ Grand Cherokee Dana 30 and Dana 44 4X4 Front Axles This kit will do one side and contains 1 upper and 1 lower.
View Details
Axles & Axle Bearings
Jeep Dana 35 Rear Axle Bearing Press-On Grand Cherokee A9 SET9
This is a genuine Dana/Spicer press on axle bearing for the Dana 35 rear axle in some Jeep’s. This is the same as the aftermarket part number A9, except it does not include the press on ring (36121) which we also have available. The number on the bearing is NP182140 and the number on the [...]
View Details