417-862-4455
Ring & Pinion Sets
Genuine Dana/Spicer 35 3:73 Ring & Pinion Gear Set Jeep Wrangler Cherokee 373 Kit Rear Axle
This is a genuine Dana/Spicer gear set in a 3:73 ratio for a Dana 35 rear differential as found in many common Jeep applications. The tooth counts are 41 on the ring gear and 11 on the pinion. This kit includes a set of ring gear bolts, pinion nut, and a crush sleeve. These are [...]
View Details
Ring & Pinion Sets
Genuine Dana/Spicer 35 4:11 Ring & Pinion Gear Set Jeep Wrangler Cherokee 411 410 4:10 Kit
This is a genuine Dana/Spicer gear set in a 4:11 ratio for a Dana 35 rear differential as found in many common Jeep applications. The tooth counts are 37 on the ring gear and 9 on the pinion. This kit includes a set of ring gear bolts, pinion nut, and a crush sleeve. These are [...]
View Details
This is a genuine Dana/Spicer gear set in a 3:54 ratio for a Dana 44 differential as found in many common GM, Chevy, Dodge, Jeep, and Ford applications. This gear set must be used on a 3:73 or faster (3:54, 3:08, etc.) carrier. This will not work in a Ford front application with a reverse [...]
View Details
This is a genuine Dana/Spicer u-joint bolt and strap kit for the GM cars and trucks with the 3R or 1344 Saginaw series pinion yoke. The Saginaw uses inside snap rings to keep the u-joint centered in the yoke. Kit includes 2 straps and 4 bolts.
View Details
Axles & Axle Bearings
GM Chevrolet Dana 60 Rear Axle Wheel Seal Semi-Float Savanah Van 2002-2010
This is a genuine Dana/Spicer rear axle seal for the super Dana 60 rear end found in 2002-2010 GM Savanah vans. These were also used in earlier Dana 60 GM applications with the semi-float rear axles (c-clip style). These are used with the 566117 axle bearing.
View Details
This is a Dana/Spicer u-joint strap kit that fits GM yokes with the 1310 or 1330 pinion yokes. This fits many common older applications. This is the same as Neapco part number 1-0024.
View Details
This is a Dana/Spicer u-joint strap kit for GM pinion yokes. This will fit 1350 and 1410 series yokes including 14 bolt 9.5, 10.5, and 11.5. This is the same as a Neapco 1-0020.
View Details
Axles & Axle Bearings
GM Chevy 1973-1991 4X4 Front Axle Outer Stub Axle Dana 44 10 Bolt Corporate
This is a genuine Dana/Spicer outer stub axle that fits 1973-1991 GM trucks with either the Dana 44 or corporate 10 bolt front end. These were also used in some Jeep and Dodge applications, and can be used to replace the 621063. Here are some specifications from Dana’s website: Brand Spicer Axle Model DANA 44 [...]
View Details
Small Parts & Seals
GM Chevy Dana 44 4X4 Front Axle Tube Seal 1968-1991 Corporate 10 Bolt
This is a genuine Dana/Spicer axle tube seal for GM applications with the Dana 44 or corporate 10 bolt 4X4 front axle.
View Details
Differential Covers
GM Dodge Ford Dana 70 Rear Differential Cover 2500 3500 F250 F350
This is a genuine Dana/Spicer cover for the Dana 70 rear differential found in many common domestic trucks. It is also stamped with the part number 42815-2.
View Details
This is a bare open differential for a Dana 60 axle with 4:56 or lower gears (4:88, 5:13, etc.). This is 30,32, or 35 spline axles. This can be used in a front or rear differential. This case comes with a set of ring gear bolts, roll pin for the cross shaft, a set of [...]
View Details
Miscellaneous
This is a genuine Dana/Spicer baffle that goes between the yoke and the outer bearing in a Dana 80 rear differential. This is 1.60″ I.D. and .032″ thick.
View Details
Axles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View Details
Differential Covers
The cover itself is a 43600-1 Stamped steel cover includes 10 bolts and fill plug 1981 – 1988 Chevy Dana 60 Front or Rear 1988 – 1998 Ford F350 Dana 60 front
View Details
Ring & Pinion Sets
This is a genuine Dana/Spicer ring & pinion in a 4:56 ratio that shows to fit trucks with the Super 70/273 axle.
View Details
This is a genuine Dana/Spicer greasable universal joint is a 1410 series. This is the same as 5-1410X except it is greasable.
View Details