417-862-4455
1973-1976 GM Chevy Dana 44 4X4 Axle Front Spindle Blazer Suburban K10 K20
$225.00
- SKU: 706528X
- Brand: Dana/Spicer
- Weight: 5.0
- Shipping: Calculated at checkout
Out of stock
This is a genuine Dana Spicer spindle for the Dana 44 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1973-1976. This also comes with the dust seals, inner bearing, and plastic thrust washer.
| Weight | 5.0 lbs |
|---|---|
| Dimensions | 6 × 6 × 6 in |
Be the first to review “1973-1976 GM Chevy Dana 44 4X4 Axle Front Spindle Blazer Suburban K10 K20”
You must be logged in to post a review.
| Make | Model | Year |
|---|---|---|
| GM/Chevy | Blazer | 1973 - 1974 |
| GM/Chevy | Blazer | 1975 - 1976 |
| GM/Chevy | K10 | 1973 - 1974 |
| GM/Chevy | K10 | 1975 - 1976 |
| GM/Chevy | K20 | 1973 - 1974 |
| GM/Chevy | K20 | 1975 - 1976 |
General Inquiries
There are no inquiries yet.
Related products
THIS IS A GENUINE DANA 44 SPINDLE WITH 5 HOLES FOR LARGE BEARING 1/2 TON DISC BRAKES APPLICATIONS. FITS MOST FORD 1976-1979 F150/F100 SERIES PICK UPS & SERVICE 1976-1978 BRONCO. THIS SPINDLE COMES WITH THE INNER BEARING, DUST SEALS, AND PLASTIC THRUST WASHER.
View Details
Miscellaneous
This is a genuine Dana/Spicer spindle bearing and seal kit for the Dana 30 or 44 4X4 front axle found in many common domestic applications, including 1973-1992 1/2 ton GM trucks, 1976-1976 Jeep vehicles, and Dodge and Ford open knuckle front ends. This kit includes the support bearing, large and small V seals, and the [...]
View Details
This is a genuine Dana/Spicer 4X4 front spindle that fit’s the following Ford applications: DANA 44 SPINDLE WITH 5 HOLES. FITS MOST FORD 1977 1/2-1979 F250 . DOES NOT FIT 76-77 LARGE EXTERNAL HUB. BEARING JOURNALS – 2.5″ OUTER & 1.625″ INNER. FLANGE DIA- 6.12″ INNER BRG DIA 2.0” // LENGTH 6.25”
View Details
This is a lower king pin bearing and seal kit for a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s. This kit does one side. 2 kits required per truck.
View Details
This is the gasket for the 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s.
View Details
This is a complete set of aftermarket spindle nuts and washers for a Dana 60 front axle. It consists of 2 each inner nut with pin, locking washer, and outer nut with the pin. These were commonly found on GM, Ford, and Dodge applications. They were also used on Dana 50 applications in Ford applications. [...]
View Details
This is a genuine Dana/Spicer 4X4 front spindle that fits some 1993-1996 Ford F150 and Bronco’s from 1993-1996 w/o ABS. If you are not sure which part number that you need, please email us with your differential tag number and we can tell for sure.
View Details
Axles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View Details
Reviews
There are no reviews yet.