417-862-4455
Dana 60 Master King Pin Kit Upper Lower Both Sides GM Chevy Ford Dodge 4X4 Front Axle
$350.00
- SKU: 706395
- Brand: Dana/Spicer
- Weight: 8.0
- Shipping: Calculated at checkout
Out of stock
This is a master king pin kit for the Dana 60 front ends from the early 1970’s to the mid 1990’s. These fit most domestic applicarions. Included parts are as follows: 2 706395X (lower kit) 2 620132 (Upper 4 bolt cap) 2 37307 (upper 4 bolt gasket) 2 620180 (upper spring seat) 2 41886 (upper nylon bushing) 2 37300 (upper spring) 2 37302 (upper srew in pin).
| Weight | 8.0 lbs |
|---|---|
| Dimensions | 6 × 4 × 2 in |
Be the first to review “Dana 60 Master King Pin Kit Upper Lower Both Sides GM Chevy Ford Dodge 4X4 Front Axle”
You must be logged in to post a review.
| Make | Model | Year |
|---|---|---|
| Dodge Ram | W350 | 1973 - 1974 |
| Dodge Ram | W350 | 1975 - 1976 |
| Dodge Ram | W350 | 1977 - 1978 |
| Dodge Ram | W350 | 1979 - 1980 |
| Dodge Ram | W350 | 1981 - 1982 |
| Dodge Ram | W350 | 1983 - 1984 |
| Dodge Ram | W350 | 1985 - 1986 |
| Dodge Ram | W350 | 1987 - 1988 |
| Dodge Ram | W350 | 1989 - 1990 |
| Dodge Ram | W350 | 1991 - 1992 |
| Dodge Ram | W350 | 1993 |
| GM/Chevy | K30 | 1973 - 1974 |
| GM/Chevy | K30 | 1975 - 1976 |
| GM/Chevy | K30 | 1977 - 1978 |
| GM/Chevy | K30 | 1979 - 1980 |
| GM/Chevy | K30 | 1981 - 1982 |
| GM/Chevy | K30 | 1983 - 1984 |
| GM/Chevy | K30 | 1985 - 1986 |
| GM/Chevy | K30 | 1987 - 1988 |
| GM/Chevy | K30 | 1989 - 1990 |
| GM/Chevy | K30 | 1991 |
General Inquiries
There are no inquiries yet.
Related products
Axles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View Details
Miscellaneous
This is a genuine Dana/Spicer spindle bearing and seal kit for the Dana 30 or 44 4X4 front axle found in many common domestic applications, including 1973-1992 1/2 ton GM trucks, 1976-1976 Jeep vehicles, and Dodge and Ford open knuckle front ends. This kit includes the support bearing, large and small V seals, and the [...]
View Details
THIS IS A GENUINE DANA 44 SPINDLE WITH 5 HOLES FOR LARGE BEARING 1/2 TON DISC BRAKES APPLICATIONS. FITS MOST FORD 1976-1979 F150/F100 SERIES PICK UPS & SERVICE 1976-1978 BRONCO. THIS SPINDLE COMES WITH THE INNER BEARING, DUST SEALS, AND PLASTIC THRUST WASHER.
View Details
This is a genuine Dana Spicer spindle for the Dana 44 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1973-1976. This is the same as part number 706528X, but it is much cheaper. This also comes with the dust seals, inner bearing, and plastic thrust washer.
View Details
This is the upper screw in pin a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details
This is an aftermarket spindle that fits Ford F150 and Bronco 4X4 front applications from 1980-1992. This is for the Dana 44 front axle. Dana has discontinued this part number.
View Details
Axles & Axle Bearings
Spindle Nut Washer Rear Hub Dana 60 Spicer Dodge Jeep Ford Lock
This is a genuine Dana/Spicer spindle nut lock washer with folding tabs. These were used in the 1960’s and 1970’s on many common Dana applications, including Dana 60 and 70 front or rear axles. The I.D. is 1 13/16″. The O.D. is 2.375″ and they are 1/16″ thick. These are the same as Dorman part [...]
View Details
This is a complete set of aftermarket spindle nuts and washers for a Dana 60 front axle. It consists of 2 each inner nut with pin, locking washer, and outer nut with the pin. These were commonly found on GM, Ford, and Dodge applications. They were also used on Dana 50 applications in Ford applications. [...]
View Details
Reviews
There are no reviews yet.