417-862-4455
2010-2013 Dodge Ram 2500/3500 Right Steering Knuckle 4X4 Front Axle 9.25 AAM
$175.00
- SKU: 40060420
- Brand: AAM American Axle Manufacturing
- Weight: 20.0
- Shipping: Calculated at checkout
Out of stock
This is a genuine AAM steering knuckle for the 9.25 4X4 front axle found in 2010-2013 Dodge Ram 2500 and 3500 series trucks. This is for the right side (passenger side). This is for the trucks with a 14 bolt front differential cover.
| Weight | 20.0 lbs |
|---|---|
| Dimensions | 14 × 14 × 6 in |
General Inquiries
There are no inquiries yet.
Related products
Axles & Axle Bearings
DANA 60 FRONT 35 SPLINE CHROMOLY DRIVE FLANGES 4X4 Front Axle Chevy Ford Dodge
This is a genuine Dana/Spicer drive flange kit for a Dana 60 4X4 front axle with 35 spline outer axles. Most factory outer axles were 30 spline. These fit GM, Ford, and Dodge applications with 55 internal splines in the hubs.
View Details
This is a master king pin kit for the Dana 60 front ends from the early 1970’s to the mid 1990’s. These fit most domestic applicarions. Included parts are as follows: 2 706395X (lower kit) 2 620132 (Upper 4 bolt cap) 2 37307 (upper 4 bolt gasket) 2 620180 (upper spring seat) 2 41886 (upper [...]
View Details
This is the upper nylon bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to mid 1990’s.
View Details
This is a lower king pin bearing and seal kit for a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s. This kit does one side. 2 kits required per truck.
View Details
This is a genuine Dana/Spicer spindle nut kit for most Dana 44 4X4 front axles in domestic trucks. This kit includes 1 inner nut with pin (21588X), 1 outer nut w/o pin (31139) and 1 washer with locking tab and holes (36569). This kit is for one side, so 2 kits are required per truck. [...]
View Details
This is a genuine Dana/Spicer 4X4 front spindle for the Dana 60 front axle found in 1980’s and early 1990’s GM and Dodge trucks. This kit includes inner spindle bearing, thrust washer, and the 2 rubber seals for the backside of the spindle. Photo shows spindle bearing installed, but they usually aren’t.
View Details
Spindles
1977-1991 GM Chevy Dana 44 4X4 Axle Front Spindle Corporate 10 Bolt Blazer Suburban K10 K20
This is a genuine Dana Spicer spindle for the Dana 44 or corporate 10 bolt 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1977-1991. This also comes with the dust seals, inner bearing, and plastic thrust washer.
View Details
This is a genuine Dana/Spicer 4X4 front spindle that fit’s the following Ford applications: DANA 44 SPINDLE WITH 5 HOLES. FITS MOST FORD 1977 1/2-1979 F250 . DOES NOT FIT 76-77 LARGE EXTERNAL HUB. BEARING JOURNALS – 2.5″ OUTER & 1.625″ INNER. FLANGE DIA- 6.12″ INNER BRG DIA 2.0” // LENGTH 6.25”
View Details