417-862-4455
3 1/4″ ID Spindle Nut Lock Washer Big Truck 3.25″ Eaton Dana/Spicer
$7.50
- SKU: 011245
- Brand: Dana/Spicer
- Weight: .30
- Shipping: Calculated at checkout
10 in stock
This is a spindle nut lock washer that has a 3.250″ inside diameter. These fit various applications.
| Weight | .30 lbs |
|---|---|
| Dimensions | 4 × 4 × 1 in |
General Inquiries
There are no inquiries yet.
Related products
Small Parts & Seals
DANA 44 SPINDLE BEARING & SEAL KIT BRONCO F150 1993-1996 FORD 4X4 FRONT AXLE
Dana 44 IFS BRONCO AND F150 1993-1996 Spindle Bearing and Seal Kit Includes 1 each Spindle Bearing (550759 or SCE2110) and V Seal, Wiper Seal (50492), and Thrust Washer (45651) as pictured.
View Details
Miscellaneous
Dana 60 4X4 Front Axle King Pin Bearing Lower Mount Chevy Ford Dodge GM 4 Bolt Flange Plate
This is a genuine Dana/Spicer lower king pin bearing mount for the Dana 60 4X4 front axle found in many GM, Ford, and Dodge applications. This has a threaded hole in the bottom for a grease zerk, although it is not included. The new Dana part number is 070SC128.
View Details
Miscellaneous
Dana 44 Corporate 10 Bolt 4X4 Front Axle Spindle Bolts Studs Steering Knuckle GM Ford Dodge Jeep
This is a genuine Dana/Spicer stud for the steering knuckle to the spindle.This fits Dana 44 and GM corporate 4X4 front axles. These are 3/8″-24 fine thread and the head of the stud is D shaped in order to clear the axle.
View Details
This is a genuine Dana/Spicer spindle nut kit for most Dana 44 4X4 front axles in domestic trucks. This kit includes 1 inner nut with pin (21588X), 1 outer nut w/o pin (31139) and 1 washer with locking tab and holes (36569). This kit is for one side, so 2 kits are required per truck. [...]
View Details
This is a spring seat that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details
Axles & Axle Bearings
Spindle Nut Washer Rear Hub Dana 60 Spicer Dodge Jeep Ford Lock
This is a genuine Dana/Spicer spindle nut lock washer with folding tabs. These were used in the 1960’s and 1970’s on many common Dana applications, including Dana 60 and 70 front or rear axles. The I.D. is 1 13/16″. The O.D. is 2.375″ and they are 1/16″ thick. These are the same as Dorman part [...]
View Details
This is a 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details
This is a genuine Dana/Spicer inner spindle nut with the pin that fits many common 4X4 applications including 1/2 ton GM trucks and SUV’s from the mid 1960’s to the early 1990’s. Also some Ford, Dodge, International, and Jeep applications. These are 1 5/8″ and 16 threads per inch.
View Details