417-862-4455
Dana Round Spindle Nut GM Ford Dodge Jeep International 6 Slot Slotted
$12.75
- SKU: 33732
- Brand: Dana/Spicer
- Weight: .30
- Shipping: Calculated at checkout
This is a genuine Dana/Spicer spindle nut. This is 2″ inside diameter and is 16TPI. This is the same as Dorman 615-130. This is used with the 33733 lock ring.
| Weight | .30 lbs |
|---|---|
| Dimensions | 2 × 2 × 1 in |
General Inquiries
There are no inquiries yet.
Related products
This is a genuine Dana/Spicer 4X4 front spindle that fit’s the following Ford applications: DANA 44 SPINDLE WITH 5 HOLES. FITS MOST FORD 1977 1/2-1979 F250 . DOES NOT FIT 76-77 LARGE EXTERNAL HUB. BEARING JOURNALS – 2.5″ OUTER & 1.625″ INNER. FLANGE DIA- 6.12″ INNER BRG DIA 2.0” // LENGTH 6.25”
View Details
Spindles
1977-1991 GM Chevy Dana 44 4X4 Axle Front Spindle Corporate 10 Bolt Blazer Suburban K10 K20
This is a genuine Dana Spicer spindle for the Dana 44 or corporate 10 bolt 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1977-1991. This also comes with the dust seals, inner bearing, and plastic thrust washer.
View Details
This is an aftermarket spindle that fits Ford F150 and Bronco 4X4 front applications from 1980-1992. This is for the Dana 44 front axle. Dana has discontinued this part number.
View Details
This is a genuine Dana Spicer spindle for the Dana 44 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1973-1976. This is the same as part number 706528X, but it is much cheaper. This also comes with the dust seals, inner bearing, and plastic thrust washer.
View Details
This is a genuine Dana Spicer spindle for the Dana 44 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1973-1976. This also comes with the dust seals, inner bearing, and plastic thrust washer.
View Details
Miscellaneous
Dana 44 Corporate 10 Bolt 4X4 Front Axle Spindle Bolts Studs Steering Knuckle GM Ford Dodge Jeep
This is a genuine Dana/Spicer stud for the steering knuckle to the spindle.This fits Dana 44 and GM corporate 4X4 front axles. These are 3/8″-24 fine thread and the head of the stud is D shaped in order to clear the axle.
View Details
Axles & Axle Bearings
Spindle Nut Washer Rear Hub Dana 60 Spicer Dodge Jeep Ford Lock
This is a genuine Dana/Spicer spindle nut lock washer with folding tabs. These were used in the 1960’s and 1970’s on many common Dana applications, including Dana 60 and 70 front or rear axles. The I.D. is 1 13/16″. The O.D. is 2.375″ and they are 1/16″ thick. These are the same as Dorman part [...]
View Details
This is the gasket for the 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s.
View Details