417-862-4455
Ford Ranger Bronco II Dana 28 IFS Inner Spindle Nut w/Pin 4X4 Front 1983-1989
$15.00
- SKU: 71526X
- Brand: Dana/Spicer
- Weight: .30
- Shipping: Calculated at checkout
46 in stock
- Front Spindle INNER NUT with PIN
- Fits FORD Bronco ll , Ranger with Manual Hubs and Dana 28 IFS Front axle
- 1983, 1984, 1985, 1986, 1987, 1988, 1989
- 1.437 ID
- 2.180 OD
- .312 THICK
Use with 40075 WASHER and 40080 OUTER NUT
| Weight | .30 lbs |
|---|---|
| Dimensions | 2 × 2 × 2 in |
General Inquiries
There are no inquiries yet.
Related products
Small Parts & Seals
Ford Straight 4X4 Front Axle Tube Dust Seal 2006+ Dana 50 & 60 F250 F350
This genuine Dana axle tube dust seal fits 2006 and newer Ford F250 and F350 dana 50 and 60 straight front axles. This seal is marked FES 5M-15197 and 53877. These are approx. 3.450″ outside diameter, which is larger than the earlier ones. This seal goes on the axle itself right behind the u-joint at [...]
View Details
Small Parts & Seals
This is a genuine AAM pinion nut washer found on GM & Dodge 3/4 and 1 ton trucks. This is to be used with nut part number 40003027.
View Details
Small Parts & Seals
Ford Straight Front Axle Steering Knuckle Seal 2006+ Dana 50 & 60
This is a genuine Dana front steering knuckle seal that fits 2006 and newer Ford F250 & F350 with either a Dana 50 or Dana 60 straight front axle. The seal is marked SKF 2017426 DANA. This seal measures approx. 5.48″ outside diameter. The original part number was 2017426.
View Details
Small Parts & Seals
Dodge Dana 44 & 60 Front Outer Stub Axle Castle Nut Also AAM 9.25 Spindle 4X4
This genuine Dana axle nut fits all Dodge front axles including Dana 44 & 60 and the AAM 9.25 found in 2003+ trucks. This is a castle nut. We also have the washer available. This is the same part as AAM 40010627.
View Details
Small Parts & Seals
This is a genuine AAM pinion yoke sleeve that fits 1999 and newer GM 3/4 and 1 ton trucks with either a 10.5 or 11.5 ring gear. This sleeve goes on the yoke and the pinion seal seals against it. We have also found on some yokes you can simply remove this sleeve and used [...]
View Details
Small Parts & Seals
GM 7.6 and 8.0 Rear Pinion Yoke Seal 1998+ AAM 7.25 S10 Camaro
This is a genuine AAM rear pinion seal that fits 1998 and newer GM trucks and SUV’s with either the 7.6 or 8.0 rear end. This is for the yoke with the factory wear sleeve on it. This also fits the later 7.25IFS with the wear sleeve on the yoke.
View Details
Small Parts & Seals
GM 7.5/7.6 Rear Axle C-Clip S10 Camaro Chevrolet 10 Bolt 7 1/2″
This is a genuine AAM c-clip for the GM 7.5/7.6 rear axle found in S10’s, Malibu’s, Camaro’s etc. These are copper colored steel. These are for both open and limited slip style carriers. 2 required per vehicle.
View Details
Small Parts & Seals
This is a genuine Dana pinion nut that fits all Dana 80 rear differentials. This nut uses an 1 7/8″ socket to remove and install it. Some yokes require a very thin wall socket. The newest Dana part number for this yoke is 2001855.
View Details