This is a genuine Dana Spicer spindle for the Dana 44 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1973-1976. This is the same as part number 706528X, but it is much cheaper. This also comes with the dust seals, inner bearing, and plastic thrust washer.
Dana 44 4X4 Front Spindle 1973-1976 K10 K20 Blazer GM Chevy Small Bearing
$54.99
- SKU: 10086725
- Brand: Dana/Spicer
- Weight: 5.0
- Shipping: Calculated at checkout
Out of stock
Weight | 5.0 lbs |
---|---|
Dimensions | 6 × 4 × 2 in |
Be the first to review “Dana 44 4X4 Front Spindle 1973-1976 K10 K20 Blazer GM Chevy Small Bearing” Cancel reply
You must be logged in to post a review.
Make | Model | Year |
---|---|---|
GM/Chevy | Blazer | 1973 - 1974 |
GM/Chevy | Blazer | 1975 - 1976 |
GM/Chevy | K10 | 1973 - 1974 |
GM/Chevy | K10 | 1975 - 1976 |
GM/Chevy | K20 | 1973 - 1974 |
GM/Chevy | K20 | 1975 - 1976 |
Related products
Axles & Axle Bearings
DANA 60 FRONT 35 SPLINE CHROMOLY DRIVE FLANGES 4X4 Front Axle Chevy Ford Dodge
This is a genuine Dana/Spicer drive flange kit for a Dana 60 4X4 front axle with 35 spline outer axles. Most factory outer axles were 30 spline. These fit GM, Ford, and Dodge applications with 55 internal splines in the hubs.
View DetailsMiscellaneous
This is a genuine Dana/Spicer spindle bearing and seal kit for the Dana 30 or 44 4X4 front axle found in many common domestic applications, including 1973-1992 1/2 ton GM trucks, 1976-1976 Jeep vehicles, and Dodge and Ford open knuckle front ends. This kit includes the support bearing, large and small V seals, and the [...]
View DetailsThis is a genuine Dana/Spicer 4X4 front spindle for the Dana 60 front axle found in 1980’s and early 1990’s GM and Dodge trucks. This kit includes inner spindle bearing, thrust washer, and the 2 rubber seals for the backside of the spindle. Photo shows spindle bearing installed, but they usually aren’t.
View DetailsThis is a genuine Dana/Spicer inner spindle nut with the pin that fits many common 4X4 applications including 1/2 ton GM trucks and SUV’s from the mid 1960’s to the early 1990’s. Also some Ford, Dodge, International, and Jeep applications. These are 1 5/8″ and 16 threads per inch.
View DetailsThis is a complete set of genuine Dana/Spicer spindle nuts and washers for a Dana 60 front axle. It consists of 2 each 621027, 621028, and 660568. These were commonly found on GM, Ford, and Dodge applications. They were also used on Dana 50 applications in Ford applications. They are 2″ 16 threads per inch. [...]
View DetailsThis is the upper screw in pin a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View DetailsThis is a genuine Dana/Spicer 4X4 front spindle that fits 1977-1991 GM K30 1 ton trucks and 1975-1998 Dodge Ram 2500 and 3500 series trucks with the Dana 60 front axle. This is the same as part number 700013, but is much cheaper. This comes with the inner bearing, 2 dust seals, and the axle [...]
View DetailsThis is a master king pin kit for the Dana 60 front ends from the early 1970’s to the mid 1990’s. These fit most domestic applicarions. Included parts are as follows: 2 706395X (lower kit) 2 620132 (Upper 4 bolt cap) 2 37307 (upper 4 bolt gasket) 2 620180 (upper spring seat) 2 41886 (upper [...]
View Details
Reviews
There are no reviews yet.