417-862-4455
Ford F150 Bronco Dana 44 Spindle 4X4 Front Axle 1993-1996
$185.89
- SKU: 707373X
- Brand: Dana/Spicer
- Weight: 5.0
- Shipping: Calculated at checkout
Out of stock
This is a genuine Dana/Spicer 4X4 front spindle that fits some 1993-1996 Ford F150 and Bronco’s from 1993-1996 w/o ABS. If you are not sure which part number that you need, please email us with your differential tag number and we can tell for sure.
| Weight | 5.0 lbs |
|---|---|
| Dimensions | 6 × 4 × 2 in |
Be the first to review “Ford F150 Bronco Dana 44 Spindle 4X4 Front Axle 1993-1996”
You must be logged in to post a review.
| Make | Model | Year |
|---|---|---|
| Ford | Bronco | 1993 - 1994 |
| Ford | Bronco | 1995 - 1996 |
General Inquiries
There are no inquiries yet.
Related products
This is a 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details
This is a lower king pin bearing and seal kit for a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s. This kit does one side. 2 kits required per truck.
View Details
Axles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View Details
This is a genuine Dana/Spicer 4X4 front spindle that fits 1977-1991 GM K30 1 ton trucks and 1975-1998 Dodge Ram 2500 and 3500 series trucks with the Dana 60 front axle. This is the same as part number 700013, but is much cheaper. This comes with the inner bearing, 2 dust seals, and the axle [...]
View Details
This is the gasket for the 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s.
View Details
Miscellaneous
This is a genuine Dana/Spicer spindle bearing and seal kit for the Dana 30 or 44 4X4 front axle found in many common domestic applications, including 1973-1992 1/2 ton GM trucks, 1976-1976 Jeep vehicles, and Dodge and Ford open knuckle front ends. This kit includes the support bearing, large and small V seals, and the [...]
View Details
This is a genuine Dana/Spicer 4X4 front spindle for the Dana 60 front axle found in 1980’s and early 1990’s GM and Dodge trucks. This kit includes inner spindle bearing, thrust washer, and the 2 rubber seals for the backside of the spindle. Photo shows spindle bearing installed, but they usually aren’t.
View Details
Miscellaneous
Dana 44 Corporate 10 Bolt 4X4 Front Axle Spindle Bolts Studs Steering Knuckle GM Ford Dodge Jeep
This is a genuine Dana/Spicer stud for the steering knuckle to the spindle.This fits Dana 44 and GM corporate 4X4 front axles. These are 3/8″-24 fine thread and the head of the stud is D shaped in order to clear the axle.
View Details
Reviews
There are no reviews yet.