417-862-4455
Dana 60 4X4 Front Spindle Ford F350 1978-1998
$109.00
- SKU: 10086724
- Brand: Dana/Spicer
- Weight: 10.0
- Shipping: Calculated at checkout
3 in stock
This is a genuine Dana/Spicer 4X4 spindle for the Dana 60 front axle in 1978-1998 Ford F350 trucks. This is the same as 700022, but is much cheaper. This includes the inner bearing, 2 dust seals, and axle thrust washer.
| Weight | 10.0 lbs |
|---|---|
| Dimensions | 12 × 12 × 12 in |
Be the first to review “Dana 60 4X4 Front Spindle Ford F350 1978-1998”
You must be logged in to post a review.
| Make | Model | Year |
|---|---|---|
| Ford | F350 | 1978 - 1979 |
| Ford | F350 | 1980 - 1981 |
| Ford | F350 | 1982 - 1983 |
| Ford | F350 | 1984 - 1985 |
| Ford | F350 | 1986 - 1987 |
| Ford | F350 | 1988 - 1989 |
| Ford | F350 | 1990 - 1991 |
| Ford | F350 | 1992 - 1993 |
| Ford | F350 | 1994 - 1995 |
| Ford | F350 | 1996 - 1997 |
| Ford | F350 | 1998 |
General Inquiries
There are no inquiries yet.
Related products
This is a genuine Dana/Spicer 4X4 front spindle for the Dana 60 front axle found in 1980’s and early 1990’s GM and Dodge trucks. This kit includes inner spindle bearing, thrust washer, and the 2 rubber seals for the backside of the spindle. Photo shows spindle bearing installed, but they usually aren’t.
View Details
This is a spring seat that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details
This is a lower king pin bearing and seal kit for a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s. This kit does one side. 2 kits required per truck.
View Details
Miscellaneous
Dana 44 Corporate 10 Bolt 4X4 Front Axle Spindle Bolts Studs Steering Knuckle GM Ford Dodge Jeep
This is a genuine Dana/Spicer stud for the steering knuckle to the spindle.This fits Dana 44 and GM corporate 4X4 front axles. These are 3/8″-24 fine thread and the head of the stud is D shaped in order to clear the axle.
View Details
Axles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View Details
This is the upper screw in pin a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details
This is an aftermarket spindle that fits Ford F150 and Bronco 4X4 front applications from 1980-1992. This is for the Dana 44 front axle. Dana has discontinued this part number.
View Details
Spindles
1977-1991 GM Chevy Dana 44 4X4 Axle Front Spindle Corporate 10 Bolt Blazer Suburban K10 K20
This is a genuine Dana Spicer spindle for the Dana 44 or corporate 10 bolt 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1977-1991. This also comes with the dust seals, inner bearing, and plastic thrust washer.
View Details
Reviews
There are no reviews yet.