417-862-4455
Dana 44 GM Corporate 10 Bolt 4X4 Front Axle Spindle Nut Washer 4 Tab With Holes Auto Locking Hubs Jeep Ford Dodge
$27.50
- SKU: 39909
- Brand: Dana/Spicer
- Weight: .30
- Shipping: Calculated at checkout
This is a genuine Dana/Spicer spindle nut washer for the Dana 44 or GM corporate 4X4 front axles that had the auto locking hubs.
| Weight | .30 lbs |
|---|---|
| Dimensions | 2 × 2 × 1 in |
General Inquiries
There are no inquiries yet.
Related products
Miscellaneous
Dana 44 Corporate 10 Bolt 4X4 Front Axle Spindle Bolts Studs Steering Knuckle GM Ford Dodge Jeep
This is a genuine Dana/Spicer stud for the steering knuckle to the spindle.This fits Dana 44 and GM corporate 4X4 front axles. These are 3/8″-24 fine thread and the head of the stud is D shaped in order to clear the axle.
View Details
THIS IS A GENUINE DANA 44 SPINDLE WITH 5 HOLES FOR LARGE BEARING 1/2 TON DISC BRAKES APPLICATIONS. FITS MOST FORD 1976-1979 F150/F100 SERIES PICK UPS & SERVICE 1976-1978 BRONCO. THIS SPINDLE COMES WITH THE INNER BEARING, DUST SEALS, AND PLASTIC THRUST WASHER.
View Details
This is a genuine Dana/Spicer 4X4 front spindle for the Dana 60 front axle found in 1980’s and early 1990’s GM and Dodge trucks. This kit includes inner spindle bearing, thrust washer, and the 2 rubber seals for the backside of the spindle. Photo shows spindle bearing installed, but they usually aren’t.
View Details
Spindles
1977-1991 GM Chevy Dana 44 4X4 Axle Front Spindle Corporate 10 Bolt Blazer Suburban K10 K20
This is a genuine Dana Spicer spindle for the Dana 44 or corporate 10 bolt 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1977-1991. This also comes with the dust seals, inner bearing, and plastic thrust washer.
View Details
Axles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View Details
This is a genuine Dana/Spicer spindle nut kit for most Dana 44 4X4 front axles in domestic trucks. This kit includes 1 inner nut with pin (21588X), 1 outer nut w/o pin (31139) and 1 washer with locking tab and holes (36569). This kit is for one side, so 2 kits are required per truck. [...]
View Details
This is a 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details
This is a master king pin kit for the Dana 60 front ends from the early 1970’s to the mid 1990’s. These fit most domestic applicarions. Included parts are as follows: 2 706395X (lower kit) 2 620132 (Upper 4 bolt cap) 2 37307 (upper 4 bolt gasket) 2 620180 (upper spring seat) 2 41886 (upper [...]
View Details