417-862-4455
1973-1992 GM Dana 44 or Corporate 10 Bolt 4X4 Front Axle Spindle Bearing & Seal kit 1976-1986 Jeep 30 Ford Dodge
$13.95
- SKU: 706527X
- Brand: Dana/Spicer
- Weight: .50
- Shipping: Calculated at checkout
10 in stock
This is a genuine Dana/Spicer spindle bearing and seal kit for the Dana 30 or 44 4X4 front axle found in many common domestic applications, including 1973-1992 1/2 ton GM trucks, 1976-1976 Jeep vehicles, and Dodge and Ford open knuckle front ends. This kit includes the support bearing, large and small V seals, and the plastic thrust washer.
| Weight | .50 lbs |
|---|---|
| Dimensions | 6 × 4 × 2 in |
General Inquiries
There are no inquiries yet.
Related products
This is a lower king pin bearing and seal kit for a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s. This kit does one side. 2 kits required per truck.
View Details
Axles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View Details
This is a 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details
This is a genuine Dana Spicer spindle for the Dana 44 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1973-1976. This also comes with the dust seals, inner bearing, and plastic thrust washer.
View Details
This is a genuine Dana/Spicer inner spindle nut with the pin that fits many common 4X4 applications including 1/2 ton GM trucks and SUV’s from the mid 1960’s to the early 1990’s. Also some Ford, Dodge, International, and Jeep applications. These are 1 5/8″ and 16 threads per inch.
View Details
This is a genuine Dana/Spicer 4X4 front spindle that fit’s the following Ford applications: DANA 44 SPINDLE WITH 5 HOLES. FITS MOST FORD 1977 1/2-1979 F250 . DOES NOT FIT 76-77 LARGE EXTERNAL HUB. BEARING JOURNALS – 2.5″ OUTER & 1.625″ INNER. FLANGE DIA- 6.12″ INNER BRG DIA 2.0” // LENGTH 6.25”
View Details
This is a genuine Dana/Spicer 4X4 front spindle for the Dana 60 front axle found in 1980’s and early 1990’s GM and Dodge trucks. This kit includes inner spindle bearing, thrust washer, and the 2 rubber seals for the backside of the spindle. Photo shows spindle bearing installed, but they usually aren’t.
View Details
Axles & Axle Bearings
Spindle Nut Washer Rear Hub Dana 60 Spicer Dodge Jeep Ford Lock
This is a genuine Dana/Spicer spindle nut lock washer with folding tabs. These were used in the 1960’s and 1970’s on many common Dana applications, including Dana 60 and 70 front or rear axles. The I.D. is 1 13/16″. The O.D. is 2.375″ and they are 1/16″ thick. These are the same as Dorman part [...]
View Details