417-862-4455
This is a genuine Dana/Spicer crush sleeve for the M300 rear differential found in late model Ford F350 and F450 series trucks.
View Details
Ring & Pinion Sets
Ford M300 Ring & Pinion Gear Set 3:73 Gearset 373 F350 Super Duty
This is a genuine Dana/Spicer gear set, in a 3:73 ratio for the M300 rear differential found in late model Ford F350 series trucks. The pinion number is 10018690 and the ring gear is 10018689. Please note that Dana does not offer a 41 spline differential for this ratio, so it can’t be used in [...]
View Details
Ring & Pinion Sets
This is a genuine Dana/Spicer gear set, in a 4:10 ratio for the M300 rear differential found in late model Ford F350 and F450 series trucks. The pinion number is 2010904 and the ring gear is 2010903. This replaces Ford part numbers LC3Z4209G or HC3Z4209K.
View Details
Ring & Pinion Sets
This is a genuine Dana/Spicer gear set, in a 4:30 ratio for the M300 rear differential found in late model Ford F350 and F450 series trucks. The pinion number is 10031773 and the ring gear is 10031772.
View Details
Front Spindle INNER NUT with PIN Fits FORD Bronco ll , Ranger with Manual Hubs and Dana 28 IFS Front axle 1983, 1984, 1985, 1986, 1987, 1988, 1989 1.437 ID 2.180 OD .312 THICK Use with 40075 WASHER and 40080 OUTER NUT
View Details
Small Parts & Seals
Ford Straight 4X4 Front Axle Tube Dust Seal 2006+ Dana 50 & 60 F250 F350
This genuine Dana axle tube dust seal fits 2006 and newer Ford F250 and F350 dana 50 and 60 straight front axles. This seal is marked FES 5M-15197 and 53877. These are approx. 3.450″ outside diameter, which is larger than the earlier ones. This seal goes on the axle itself right behind the u-joint at [...]
View Details
Small Parts & Seals
Ford Straight Front Axle Steering Knuckle Seal 1998.5-2005 Dana 50 & 60
This is a genuine Dana front steering knuckle seal that fits 1998.5-2005 Ford F250 & F350 with either a Dana 50 or Dana 60 straight front axle. The seal is marked FRESHEDA 5H-15052 A085824 RDS 81. This seal measures approx. 4.46″ outside diameter
View Details
Small Parts & Seals
Ford Straight Front Axle Steering Knuckle Seal 2006+ Dana 50 & 60
This is a genuine Dana front steering knuckle seal that fits 2006 and newer Ford F250 & F350 with either a Dana 50 or Dana 60 straight front axle. The seal is marked SKF 2017426 DANA. This seal measures approx. 5.48″ outside diameter. The original part number was 2017426.
View Details
Small Parts & Seals
Ford Straight Front Axle Tube Dust Seal 1998.5-2005 Dana 50 & 60
This genuine Dana axle tube dust seal fits 1998.5-2005 Ford F250 and F350 dana 50 and 60 straight front axles. This seal is marked FORSHEDA 11 10.060 D768-11 50381.These are approx. 3.125″ outside diameter, which is smaller than the later ones. This seal goes on the axle itself right behind the u-joint at the end [...]
View Details
Small Parts & Seals
Front Axle Shaft Tube Seal fits 2007-2018 Jeep Wrangler JK Rubicon or Non-Rubicon Dana 30 44 4X4
This is a genuine Dana/Spicer axle tube seal for the Dana 30 or 44 4X4 front axle found in 2007-2018 Jeep Wrangler JK’s, including Rubicon.
View Details
Ring & Pinion Sets
Genuine Dana 70 Ring and Pinion 4:10 Ratio Chevy Ford Dodge 410
This is a genuine Dana ring and pinion set in a 4:10 ratio that fits Chevy, Ford, and Dodge Dana 70 applications with the common 5/8″ pinion offset. Must be uses with a 4:10 and numerically lower differential carrier. Ring gear part number is 34840 and the pinion is 40959. Tooth counts are 41 (ring [...]
View Details
Ring & Pinion Sets
Genuine Dana 80 3:73 Thin Ring Gear Pinion Kit Set Ford Rear Differential
This is a genuine Dana 80 ring gear and pinion set in a 3:73 ratio. The tooth counts are 41 on the ring gear and 11 on the pinion. The part number on the ring gear is 2018598 and the pinion is 50546. These will fit some Fords depending on the application as some Fords [...]
View Details
This is a genuine Dana ring and pinion set in a 4:30 ratio that fits Chevy, Ford, and Dodge applications. Must be uses with a 4:10 and numerically higher differential carrier. Ring gear part number is 50555 and the pinion is 50554. Tooth counts are 43 (ring gear) and 10 (pinion). These sets are Made [...]
View Details
Ring & Pinion Sets
Genuine Dana 80 4:63 Ring & Pinion Set Chevy Ford Dodge 463 Made in U.S.A.
This is a genuine Dana ring and pinion set in a 4:63 ratio that fits Chevy, Ford, and Dodge applications. Must be uses with a 4:10 and numerically higher differential carrier. Ring gear part number is 42420 and the pinion is 42419. Tooth counts are 37 (ring gear) and 8 (pinion). These sets are Made [...]
View Details
Ring & Pinion Sets
Genuine Dana 80 4:88 Ring Gear & Pinion Set GM Ford Dodge 488
This is a genuine Dana ring and pinion set in a 4:88 ratio. This is a bare gearset with no bearings or seals. This can be used in Chevy, Ford, and Dodge applications.
View Details
Ring & Pinion Sets
Genuine Dana 80 Ring & Pinion 5:13 Chevy Ford Dodge Made in U.S.A.
This is a genuine Dana ring and pinion set in a 5:13 ratio that fits Chevy, Ford, and Dodge applications. Must be uses with a 4:10 and numerically higher differential carrier. Ring gear part number is 46978 and the pinion is 44842. Tooth counts are 41 (ring gear) and 8 (pinion). These sets are Made [...]
View Details