417-862-4455
Dana 44 Spindle Nut Kit 4X4 Front Axle GM Ford Jeep International Dodge
$11.00
- SKU: 28068X
- Brand: Dana/Spicer
- Weight: .5
- Shipping: Calculated at checkout
This is a genuine Dana/Spicer spindle nut kit for most Dana 44 4X4 front axles in domestic trucks. This kit includes 1 inner nut with pin (21588X), 1 outer nut w/o pin (31139) and 1 washer with locking tab and holes (36569). This kit is for one side, so 2 kits are required per truck. 2 kits are also the same as Warn 33720 spindle nut kit, used to replace automatic locking hubs on Ford applications.
| Weight | .5 lbs |
|---|---|
| Dimensions | 6 × 4 × 2 in |
Reviews
There are no reviews yet.
| Make | Model | Year |
|---|---|---|
| Ford | F150 | 1973 - 1974 |
| Ford | F150 | 1975 - 1976 |
| Ford | F150 | 1977 - 1978 |
| Ford | F150 | 1979 - 1980 |
| Ford | F150 | 1981 - 1982 |
| Ford | F150 | 1983 - 1984 |
| Ford | F150 | 1985 - 1986 |
| Ford | F150 | 1987 - 1988 |
| Ford | F150 | 1989 - 1990 |
| Ford | F150 | 1991 - 1992 |
| Ford | F150 | 1993 - 1994 |
| Ford | F150 | 1995 - 1996 |
| Ford | F150 | 1997 - 1998 |
| Ford | F250 | 1973 - 1974 |
| Ford | F250 | 1975 - 1976 |
| Ford | F250 | 1977 - 1978 |
| Ford | F250 | 1979 - 1980 |
| Ford | F250 | 1981 - 1982 |
| Ford | F250 | 1983 - 1984 |
| Ford | F250 | 1985 - 1986 |
| Ford | F250 | 1987 - 1988 |
| Ford | F250 | 1989 - 1990 |
| Ford | F250 | 1991 - 1992 |
| Ford | F250 | 1993 - 1994 |
| Ford | F250 | 1995 - 1996 |
| Ford | F250 | 1997 - 1998 |
| GM/Chevy | Blazer | |
| GM/Chevy | K10 | |
| GM/Chevy | K20 |
Related products
This is a genuine Dana Spicer spindle for the Dana 44 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1973-1976. This also comes with the dust seals, inner bearing, and plastic thrust washer.
View Details
This is the upper screw in pin a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details
Small Parts & Seals
This is a Dana 80 pinion yoke that mostly shows to fit Ford applications with the 1480 series u-joints. May have to remove the tin dust shield for seal clearance.
View Details
This is a genuine Dana/Spicer 4X4 spindle for the Dana 60 front axle in 1978-1998 Ford F350 trucks. This is the same as 700022, but is much cheaper. This includes the inner bearing, 2 dust seals, and axle thrust washer.
View Details
This is a complete set of genuine Dana/Spicer spindle nuts and washers for a Dana 60 front axle. It consists of 2 each 621027, 621028, and 660568. These were commonly found on GM, Ford, and Dodge applications. They were also used on Dana 50 applications in Ford applications. They are 2″ 16 threads per inch. [...]
View Details
This is a master king pin kit for the Dana 60 front ends from the early 1970’s to the mid 1990’s. These fit most domestic applicarions. Included parts are as follows: 2 706395X (lower kit) 2 620132 (Upper 4 bolt cap) 2 37307 (upper 4 bolt gasket) 2 620180 (upper spring seat) 2 41886 (upper [...]
View Details
Small Parts & Seals
271 & 273 Dodge Transfer Case Large Booted Rear Seal 271D 273D 2003+
This is the large booted seal for the rear of a 271 or 273 Dodge transfer case with a rear slip yoke. The New Venture part number is 38249. These are almost impossible to get at your local auto parts store. These are used with the 45379 rear bushing. This seal can also be used [...]
View Details
Small Parts & Seals
This is the outer axle nut washer that goes with the 46085 axle nut on 4X4 Dodge front axles, this fits Dana 44 and 60 as well as the AAM 9.25 front axle found in 2003 and newer Dodge Ram 2500 and 3500 series trucks.
View Details
Be the first to review “Dana 44 Spindle Nut Kit 4X4 Front Axle GM Ford Jeep International Dodge”
You must be logged in to post a review.