417-862-4455
Inner Spindle Nut Ford Ranger 4X4 Front Axle 1990-1997 Dana 28 1993-1997 Dana 35
$13.50
- SKU: 74078X
- Brand: Dana/Spicer
- Weight: .40
- Shipping: Calculated at checkout
6 in stock
This is a genuine Dana/Spicer inner spindle nut for 1990-1997 Ford Rangers with either a Dana 28 or Dana 35 front axle. This is for trucks with manual locking hubs. This is the inner nut with the pin. These are 1.625-16 TPI.
| Weight | .40 lbs |
|---|---|
| Dimensions | 2 × 2 × 1 in |
General Inquiries
There are no inquiries yet.
Related products
Miscellaneous
Dana 60 4X4 Front Axle King Pin Bearing Lower Mount Chevy Ford Dodge GM 4 Bolt Flange Plate
This is a genuine Dana/Spicer lower king pin bearing mount for the Dana 60 4X4 front axle found in many GM, Ford, and Dodge applications. This has a threaded hole in the bottom for a grease zerk, although it is not included. The new Dana part number is 070SC128.
View Details
Axles & Axle Bearings
DANA 60 FRONT 35 SPLINE CHROMOLY DRIVE FLANGES 4X4 Front Axle Chevy Ford Dodge
This is a genuine Dana/Spicer drive flange kit for a Dana 60 4X4 front axle with 35 spline outer axles. Most factory outer axles were 30 spline. These fit GM, Ford, and Dodge applications with 55 internal splines in the hubs.
View Details
This is a genuine Dana/Spicer 4X4 front spindle for the Dana 60 front axle found in 1980’s and early 1990’s GM and Dodge trucks. This kit includes inner spindle bearing, thrust washer, and the 2 rubber seals for the backside of the spindle. Photo shows spindle bearing installed, but they usually aren’t.
View Details
This is a genuine Dana/Spicer 4X4 front spindle for Ford F350 trucks from 1978-1997 with the Dana 60 front axle. This kit includes the inner spindle bearing, thrust washer, and 2 rubber seals for the back side of the spindle.
View Details
This is a genuine Dana Spicer spindle for the Dana 44 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1973-1976. This is the same as part number 706528X, but it is much cheaper. This also comes with the dust seals, inner bearing, and plastic thrust washer.
View Details
This is a genuine Dana/Spicer spindle nut kit for most Dana 44 4X4 front axles in domestic trucks. This kit includes 1 inner nut with pin (21588X), 1 outer nut w/o pin (31139) and 1 washer with locking tab and holes (36569). This kit is for one side, so 2 kits are required per truck. [...]
View Details
This is a 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details
Axles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View Details