fbpx

Axles & Axle Bearings

Showing 145–160 of 166 results

$95.00

REAR AXLE SHAFT – GM 10.5 AXLE – 14 BOLT – 30 SPLINE – SHAFT LENGTH 38.98 IN. Brand SVL Axle Model GM 10.5 Material Steel Axle Cover Bolt Hole Qty 14 Location RH Axle Length (In) 38.980 Length (IN) 38.980 Spline Count 30 Axle Spline Count 30 Bolt Pattern 8 X 3.56 Wheel Stud [...]

View Details
$49.98

This is a genuine Dana/Spicer outer stub axle that fits 1973-1991 GM  trucks with either the Dana 44 or corporate 10 bolt front end. These were also used in some Jeep and Dodge applications, and can be used to replace the 621063. Here are some specifications from Dana’s website: Brand Spicer Axle Model DANA 44 [...]

View Details
$125.00

This is a genuine AAM rear axle shaft for GM 3500 series trucks from 2001-2010 with the narrow track rear end. This axle measures 913mm or 35.9449″ long from the back of the flange, and is 30 spline. The original GM part number was 15898643.

View Details
$28.00

This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.

View Details
$35.00

This is a genuine AAM axle bearing and seal kit for the GM 8.25 IFS differential. This kit fits 1997 and newer Chevy 1/2 ton trucks ans SUV’s and does both sides.

View Details
$45.00

This is a genuine AAM axle bearing and seal kit for the GM 9.25 IFS differential as well as thrust washers and axle retaining clips. This kit fits 1998-2013 3/4 and 1 ton trucks.

View Details
$125.00

This is a genuine AAM axle for the 14 bolt 10.5 that measures 39″ long. It is 30 spline. This fits various GM and Chevrolet trucks. Buyer is responsible for application. We are selling it by part number and length only and do not guarantee it to fit any specific vehicle.

View Details
$85.00

– 27 spline – 6.11″ long – Fits Dana Spicer 30 in Jeeps – Outer stub – 5-260X U-joint size – Chromoly USED IN 1987 TO 1988 AND 1990-1991 The original part number (40611) has been discontinued.

View Details
$22.74

This is a genuine Dana/Spicer press on axle bearing for the Dana 35 rear axle in some Jeep’s. This is the same as the aftermarket part number A9, except it does not include the press on ring (36121) which we also have available. The number on the bearing is NP182140 and the number on the [...]

View Details
$8.78

This is a genuine Dana/Spicer press on sleeve that goes up against the press on bearing on a Jeep with a Dana 35 rear axle. These were usually found in Grand Cherokee’s. The inside diameter is 1.368″. This goes with bearing number 566075.

View Details
$6.85

This is a genuine Dana rear axle seal for the Dana 35 rear axle in mid 1990’2 to mid 2000’s Jeep Grand Cherokee’s. This is used with the 566075 axle bearing and is the same as National 2146.

View Details
$42.50

This is a genuine Dana/Spicer rear axle bearing kit for Dana 44 rear axles with press on bearings. This is a common setup for older Jeeps, Fords, and possibly Internationals. Please be aware that these are larger bearings for the older Dana 44 axles and will not fit the later Super 44 axles. This kit [...]

View Details
$42.26

This is a genuine Dana outer stub axle that fits most Jeeps 1995-2006. Including Wrangles and Cherokee’s. If you are unsure of your application feel fre to email us with your axle tag number or application.

View Details
$225.00

This is a genuine Dana/Spicer leftt hand axle shaft that shows to fit 2007-2013 Jeep JK Wrangler with the Dana 30 front differential.

View Details
$275.00

This is a genuine AAM left front axle assembly for the 9.25 front differential found in 2014+  Dodge Ram 2500 and 3500 series 4X4 trucks. The AAM part number is 40104193. This is for the axle with the disconnect on the right side and the 12 bolt cover. The new part number for this axle [...]

View Details
$95.00

This is a genuine Dana Spicer outer stub axle for a Dana 60 Front axle. This Is An Upgrade To The 35 Spline From The Stock 30 Spline. These are a non-stock spline. All the originals were 30 spline. Must use 35 spline lockout hubs or slugs. Chevy 1 Ton  1977-1990 Dodge W200 and W250 [...]

View Details