417-862-4455
2003-2008 Dodge Ram 2500/3500 Left Steering Knuckle 4X4 Front Axle 9.25 AAM
$175.00
- SKU: 40014593
- Brand: AAM American Axle Manufacturing
- Weight: 20.0
- Shipping: Calculated at checkout
Out of stock
This is a genuine AAM steering knuckle for the 9.25 4X4 front axle found in 2003-2008 Dodge Ram 2500 and 3500 series trucks. This is for the left side (driver side).
| Weight | 20.0 lbs |
|---|---|
| Dimensions | 12 × 12 × 6 in |
General Inquiries
There are no inquiries yet.
Related products
This is a genuine Dana/Spicer 4X4 spindle for the Dana 60 front axle in 1978-1998 Ford F350 trucks. This is the same as 700022, but is much cheaper. This includes the inner bearing, 2 dust seals, and axle thrust washer.
View Details
This is a genuine Dana/Spicer 4X4 front spindle that fit’s the following Ford applications: DANA 44 SPINDLE WITH 5 HOLES. FITS MOST FORD 1977 1/2-1979 F250 . DOES NOT FIT 76-77 LARGE EXTERNAL HUB. BEARING JOURNALS – 2.5″ OUTER & 1.625″ INNER. FLANGE DIA- 6.12″ INNER BRG DIA 2.0” // LENGTH 6.25”
View Details
This is a genuine Dana/Spicer 4X4 front spindle that fits 1977-1991 GM K30 1 ton trucks and 1975-1998 Dodge Ram 2500 and 3500 series trucks with the Dana 60 front axle. This is the same as part number 700013, but is much cheaper. This comes with the inner bearing, 2 dust seals, and the axle [...]
View Details
This is a complete set of aftermarket spindle nuts and washers for a Dana 60 front axle. It consists of 2 each inner nut with pin, locking washer, and outer nut with the pin. These were commonly found on GM, Ford, and Dodge applications. They were also used on Dana 50 applications in Ford applications. [...]
View Details
This is a master king pin kit for the Dana 60 front ends from the early 1970’s to the mid 1990’s. These fit most domestic applicarions. Included parts are as follows: 2 706395X (lower kit) 2 620132 (Upper 4 bolt cap) 2 37307 (upper 4 bolt gasket) 2 620180 (upper spring seat) 2 41886 (upper [...]
View Details
This is the upper nylon bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to mid 1990’s.
View Details
Axles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View Details
This is a genuine Dana Spicer spindle for the Dana 44 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1973-1976. This is the same as part number 706528X, but it is much cheaper. This also comes with the dust seals, inner bearing, and plastic thrust washer.
View Details