417-862-4455
Aftermarket 1977-1991 GM Chevy Dana 44 4X4 Axle Front Spindle Corporate 10 Bolt Blazer Suburban K10 K20
$95.00
- SKU: 706570XB
- Brand: RAJ International Trading
- Weight: 5.0
- Shipping: Calculated at checkout
6 in stock
This is an aftermarket spindle for the Dana 44 or corporate 10 bolt 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburban’s from 1977-1991. The Dana part number is 706570X. This is a bare spindle with no bearings or seals.
| Weight | 5.0 lbs |
|---|---|
| Dimensions | 6 × 6 × 8 in |
General Inquiries
There are no inquiries yet.
Related products
This is a genuine Dana/Spicer 4X4 front spindle for the Dana 60 front axle found in 1980’s and early 1990’s GM and Dodge trucks. This kit includes inner spindle bearing, thrust washer, and the 2 rubber seals for the backside of the spindle. Photo shows spindle bearing installed, but they usually aren’t.
View Details
This is a genuine Dana/Spicer 4X4 front spindle that fits some 1993-1996 Ford F150 and Bronco’s from 1993-1996 w/o ABS. If you are not sure which part number that you need, please email us with your differential tag number and we can tell for sure.
View Details
Miscellaneous
Dana 44 Corporate 10 Bolt 4X4 Front Axle Spindle Bolts Studs Steering Knuckle GM Ford Dodge Jeep
This is a genuine Dana/Spicer stud for the steering knuckle to the spindle.This fits Dana 44 and GM corporate 4X4 front axles. These are 3/8″-24 fine thread and the head of the stud is D shaped in order to clear the axle.
View Details
This is a master king pin kit for the Dana 60 front ends from the early 1970’s to the mid 1990’s. These fit most domestic applicarions. Included parts are as follows: 2 706395X (lower kit) 2 620132 (Upper 4 bolt cap) 2 37307 (upper 4 bolt gasket) 2 620180 (upper spring seat) 2 41886 (upper [...]
View Details
This is a genuine Dana/Spicer 4X4 front spindle that fit’s the following Ford applications: DANA 44 SPINDLE WITH 5 HOLES. FITS MOST FORD 1977 1/2-1979 F250 . DOES NOT FIT 76-77 LARGE EXTERNAL HUB. BEARING JOURNALS – 2.5″ OUTER & 1.625″ INNER. FLANGE DIA- 6.12″ INNER BRG DIA 2.0” // LENGTH 6.25”
View Details
This is a genuine Dana/Spicer 4X4 front spindle that fits 1977-1991 GM K30 1 ton trucks and 1975-1998 Dodge Ram 2500 and 3500 series trucks with the Dana 60 front axle. This is the same as part number 700013, but is much cheaper. This comes with the inner bearing, 2 dust seals, and the axle [...]
View Details
Axles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View Details
This is the upper screw in pin a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details