417-862-4455
1980-1998 Ford F250 F350 Dana 50 IFS 4X4 Front Axle Spindle
$95.00
- SKU: 708085B
- Brand: RAJ International Trading
- Weight: 10
- Shipping: Calculated at checkout
3 in stock
This is an aftermarket 4X4 spindle for the Dana 50 IFS front axle found in many 1980-1998 Ford F250 trucks. These were also used in some F350 trucks. This is a 5 bolt spindle. The original Dana part number was 708085. This is a bare spindle, with no bearings or seals.
| Weight | 10 lbs |
|---|---|
| Dimensions | 6 × 6 × 10 in |
General Inquiries
There are no inquiries yet.
Related products
Axles & Axle Bearings
DANA 60 FRONT 35 SPLINE CHROMOLY DRIVE FLANGES 4X4 Front Axle Chevy Ford Dodge
This is a genuine Dana/Spicer drive flange kit for a Dana 60 4X4 front axle with 35 spline outer axles. Most factory outer axles were 30 spline. These fit GM, Ford, and Dodge applications with 55 internal splines in the hubs.
View Details
This is a master king pin kit for the Dana 60 front ends from the early 1970’s to the mid 1990’s. These fit most domestic applicarions. Included parts are as follows: 2 706395X (lower kit) 2 620132 (Upper 4 bolt cap) 2 37307 (upper 4 bolt gasket) 2 620180 (upper spring seat) 2 41886 (upper [...]
View Details
This is a spring seat that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details
This is a genuine Dana/Spicer 4X4 front spindle that fit’s the following Ford applications: DANA 44 SPINDLE WITH 5 HOLES. FITS MOST FORD 1977 1/2-1979 F250 . DOES NOT FIT 76-77 LARGE EXTERNAL HUB. BEARING JOURNALS – 2.5″ OUTER & 1.625″ INNER. FLANGE DIA- 6.12″ INNER BRG DIA 2.0” // LENGTH 6.25”
View Details
This is a genuine Dana/Spicer 4X4 front spindle for Ford F350 trucks from 1978-1997 with the Dana 60 front axle. This kit includes the inner spindle bearing, thrust washer, and 2 rubber seals for the back side of the spindle.
View Details
This is a complete set of aftermarket spindle nuts and washers for a Dana 60 front axle. It consists of 2 each inner nut with pin, locking washer, and outer nut with the pin. These were commonly found on GM, Ford, and Dodge applications. They were also used on Dana 50 applications in Ford applications. [...]
View Details
This is a genuine Dana/Spicer 4X4 front spindle that fits 1977-1991 GM K30 1 ton trucks and 1975-1998 Dodge Ram 2500 and 3500 series trucks with the Dana 60 front axle. This is the same as part number 700013, but is much cheaper. This comes with the inner bearing, 2 dust seals, and the axle [...]
View Details
Miscellaneous
Dana 44 Corporate 10 Bolt 4X4 Front Axle Spindle Bolts Studs Steering Knuckle GM Ford Dodge Jeep
This is a genuine Dana/Spicer stud for the steering knuckle to the spindle.This fits Dana 44 and GM corporate 4X4 front axles. These are 3/8″-24 fine thread and the head of the stud is D shaped in order to clear the axle.
View Details