fbpx

Showing 273–288 of 431 results

$13.95

This is a genuine AAM driveshaft boot kit for the slip yoke in the rear driveshaft at the carrier bearing. This fits GM and Dodge 3/4 and 1 ton applications from 2003-2018. This boot only fits the AAM driveshaft. Please be aware that Dana made some of the factory drivelines for these trucks as well. [...]

View Details
$29.95

This is a genuine AAM rear differential cover for 2003+ Dodge 3/4 and 1 ton trucks with the 11.5 ring gear. This is virtually identical to the one for the GM trucks, although the part numbers are different according to AAM’s website.

View Details
$90.00

This is a genuine AAM 271-273 Transfer Case Slip Yoke w/balancer 1410/1415 U-Joint. These were used on 2003+ Dodge Ram 2500 and 3500 series trucks with the 271 or 273 New Process transfer case. 2.29961″ O.D. 9.39370″ Long 34 Spline 1.74803 Diameter. Please be sure of your u-joint size before ordering as some of these [...]

View Details
$395.00

This is a genuine AAM ring and pinion in a 4:56 ratio for Dodge Ram 2500 series trucks with the 10.5 rear axle. Please beware that some 2500 trucks had the 11.5 rear axle.

View Details
$46.00

This is a genuine AAM differential cover kit for the 10.5 rear differential found in some 2003 and newer Dodge Ram 2500 trucks. These were usually found in trucks with a gas engine. This kit includes the cover, gasket, 14 bolts, and a fill plug.

View Details
$65.00

This is a genuine AAM driveshaft flange yoke that fits the rear driveline where it bolts to the rear pinion flange. This is for the 1555 series universal joint. This mates with the 40062272 4 bolt pinion flange.

View Details
$45.00

This is a genuine AAM axle tube seal kit for the 2003 and newer Dodge Ram 2500 and 3500 series trucks with the 9.25 4X4 front axle.

View Details
$12.50

This is a genuine AAM rubber cover gasket for the 9.25 4X4 front axle found in 2014 and newer Dodge Ram 2500 and 3500 series trucks. This is for the 12 bolt cover.

View Details
$2.00

Fits 2003-2016 Dodge Ram 2500 and 3500 with AAM 9.25 inch 4X4 front end. This is the bolt that bolts the hub bearing assembly to the steering knuckle. There are 4 bolts on either side. Price is per bolt. Buy as many as you need.   

View Details
$85.00

This is a genuine AAM axle gear/internal kit for the Dodge 9.25 front end found in 2007 and newer 3/4 and 1 ton trucks. Please note the smaller pinion gears are rounded where they contact the carrier and use thin thrust washers. From 2003-2006 Dodge used the same internal kit as the GM trucks which [...]

View Details
$40.00

This is a genuine AAM cover kit for the 11.5 rear differential found in 2003 and newer Dodge Ram 2500 and 3500 series trucks. This kit includes the cover, rubber gasket, bolts, and a fill plug.

View Details
$80.00

This is a genuine AAM slip yoke that fits the 271 or 273 transfer case found in 2003-2011 Dodge Ram 2500 and 3500 series trucks. Technical specifications, 2.299″ Ground Hub (barrel diameter), 1.74803 spline diameter 34 spline, 9.550″ C/l to end. This slip uses the AAM u-joint number 74081485.  Please check the u-joint size in [...]

View Details
$495.00

This is a genuine AAM Posi Trac differntial for the Ford 10.25 rear end. These have 35 spline axle gears. This can be used as a low cost alternative to the 3 pinion posi found in the 1999 and newer Ford F250’s and F350’s.

View Details
$59.00

This is a genuine AAM tone ring for a 10.25 or 10.5 Ford rear differential found in 1985 to current production 3/4 and 1 ton trucks.

View Details
$175.00

This is a genuine AAM spider gear kit for the 10.5 rear differential found in 1999 and newer Ford F250 and F350 trucks. This is for the 3 pinion gear setup and is for the open differential, not for the limited slip differential. For some reason the Y or cross is not included with this [...]

View Details
$900.00

This is a genuine AAM 3 pinion Posi for the 10.5 Ford differential found in 1999 and newer F250 and F350 trucks. This is the later 3 pinion design.

View Details