417-862-4455No products in the cart.
Transmission Parts
$550.00
This is a genuine Dana/Spicer Trac Lok differential for a Dana 60 with 35 spline axles. This comes with a set of ring gear bolts, side bearings, and inboard and outboard shims. This fits many application including most 4X4 front axles.
View Details
Ring & Pinion Sets
Dana 60 4:10 Reverse Cut Ford Ring & Pinion Gear Set 4X4 Front F350
$330.00
This is a genuine Dana 4:10 gearset for a Dana 60 reverse cut in a Ford F350 front axle. This kit includes both pinion bearings and races, crush sleeve, pinion seal, nut, shims, and ring gear bolts. This pinion is made for a crush sleeve rather than preload shims. These were primarily used in 1999 [...]
View Details
$510.00
This is a genuine Dana 4:10 gearset for a Dana 60 reverse cut in a Ford F350 front axle. This kit includes both pinion bearings and races, pinion seal, nut, shims, and ring gear bolts. This pinion is made for preload shims rather than a crush sleeve.
View Details
Ring & Pinion Sets
$525.00
This is a genuine Dana 60 4:10 ring and pinion set for the front or rear in a GM or Dodge application, or the rear of a Ford truck. This is a gear kit that includes both pinion bearings and races, ring gear bolts, pinion seal, pinion nut and washer, and shims. If you purchase [...]
View Details
Ring & Pinion Sets
$275.00
This is a genuine Dana 60 4:88 ring and pinion set for the front or rear in a GM or Dodge application, or the rear of a Ford truck. This gear set uses preload shims instead of a crush sleeve. Tooth counts are 39 on the ring gear and 8 on the pinion.
View Details
Miscellaneous
Dana 60 4X4 Front Axle King Pin Bearing Lower Mount Chevy Ford Dodge GM 4 Bolt Flange Plate
$19.95
This is a genuine Dana/Spicer lower king pin bearing mount for the Dana 60 4X4 front axle found in many GM, Ford, and Dodge applications. This has a threaded hole in the bottom for a grease zerk, although it is not included. The new Dana part number is 070SC128.
View Details
Axles & Axle Bearings
Dana 60 4X4 Front Axle Spindle Bearing Dust Seal Kit Ford GM Chevy Dodge 1980-1993 K3500
$19.95
This is a genuine Dana/Spicer spindle bearing kit for the Dana 60 4X4 front axles found in GM, Ford, and Dodge applications prior to the use of hub bearing assemblies. These were usually prior to 1992. This kit includes the inner spindle bearing, plastic thrust washer, and the big and small rubber dust seals.
View Details
Out of stock
$239.00
This is a genuine Dana/Spicer 4X4 front spindle for the Dana 60 front axle found in 1980’s and early 1990’s GM and Dodge trucks. This kit includes inner spindle bearing, thrust washer, and the 2 rubber seals for the backside of the spindle. Photo shows spindle bearing installed, but they usually aren’t.
View Details
Small Parts & Seals
Dana 60 4X4 Front Axle Tube Seals Chevy Ford Dodge 1970-1991
$7.50
This is a genuine Dana/Spicer axle tube seal that fits most domestic GM, Ford, and Dodge applications from 1970-1991 without a disconnect. 2 are required per truck.
View Details
Axles & Axle Bearings
Dana 60 4X4 Front Axle Wheel Hub Inner Bearing Ford Dodge 1979-1997
$24.95
This is a genuine Dana/Spicer 4X4 front hub seal that fits many common Ford and Dodge applications. Including Ford from 1979-1997, and Dodge from 1979-1993. The bearing is a 387A and the race is a 382A.
View Details
Small Parts & Seals
Dana 60 4X4 Front Axle Wheel Hub Seal Chevy Ford Dodge 1979-1997
$7.00
This is a genuine Dana/Spicer 4X4 front hub seal that fits many common GM, Ford, and Dodge applications. Including GM from 1979-1991, Ford from 1979-1997, and dodge from 1979-1993. The seal has an SKF number on it of 27471. This will replace National seal numbers 415960 and 415009.
View Details
Small Parts & Seals
$2.95
This is a genuine Dana/Spicer snap ring that goes on the outer axle on a Dana 60 4X4 front axle. This fits most GM and Dodge trucks that use a snap ring out by the lockout hubs. We have to buy them 25 at a time from Dana. but we sell them individually.
View Details
$85.00
This is a genuine Dana/Spicer 4X4 front spindle that fits 1977-1991 GM K30 1 ton trucks and 1975-1998 Dodge Ram 2500 and 3500 series trucks with the Dana 60 front axle. This is the same as part number 700013, but is much cheaper. This comes with the inner bearing, 2 dust seals, and the axle [...]
View Details
$75.00
This is a genuine Dana/Spicer 4X4 spindle for the Dana 60 front axle in 1978-1998 Ford F350 trucks. This is the same as 700022, but is much cheaper. This includes the inner bearing, 2 dust seals, and axle thrust washer.
View Details
Ring & Pinion Sets
$295.00
This is a genuine Dana/Spicer ring and pinion in a 5:38 ratio for a Dana 60 regular rotation differential. These were used in GM and Dodge trucks (front or rear) and Ford trucks (rear only). Tooth counts are 43 on the ring gear and 8 on the pinion.
View Details
Out of stock
Ring & Pinion Sets
Dana 60 5:86 Gear Set Ring & Pinion 586 GM Chevy Ford Dodge Jeep International Standard Rotation
$195.00
This is a genuine Dana/Spicer ring and pinion for a regular standard rotation Dana 60 axle. This fits most domestic applications for Dana 60 rear axles, and GM and Dodge 4X4 front axle applications. The tooth counts are 41-7. The ring gear number is 34717 and the pinion is a 34718.
View Details