417-862-4455
This is a genuine Dana/Spicer bearing kit for the Dana 35 or M200 rear differential found in some 2018 and newer Jeep JL vehicles. This kit includes both pinion bearings and races, both differential bearings and races, pinion seal, crush sleeve, and nut.
View Details
Traction Devices
Dana 35 Jeep Rear Axle Posi Trac Lok Differential Limited Slip 27 Spline 3:31 and Faster
This is a genuine Dana Trac Lok differential for the Jeep Dana 35 rear differential with 3:31 or higher (3:08, 2:73, etc.) gear ratios and 27 spline axles. This kit includes ring gear bolts and differential side bearings.
View Details
Traction Devices
Dana 35 Jeep Rear Axle Posi Trac Lok Differential Limited Slip 27 Spline 3:54 and Down
This is a genuine Dana Trac Lok differential for the Jeep Dana 35 rear differential with 3:54 or lower (3:73, 4:10, etc.) gear ratios and 27 spline axles. This kit includes ring gear bolts and differential side bearings.
View Details
Ring & Pinion Sets
Dana 35 Jeep Wrangler 410 411 4:10 4:11 Gear Set Kit Cherokee XJ YJ TJ Ring & Pinion Gearset
This is a genuine Dana ring and pinion gear kit for the Dana 35 rear axle found in various model Jeeps from 1987-2004. This kit includes the ring and pinion, inner pinion bearing & race, outer pinion bearing & race, pinion seal, crush sleeve, nut, and ring gear bolts. This is actually a 411 (9-37). [...]
View Details
This is a genuine Dana/Spicer loaded open differential carrier for 3:55 and numerically higher (3:07 3:08 3:31). This fits many Jeep applications from the late 1980’s-2006. This carrier comes with the 2 differential side bearings and a set of ring gear bolts. The Jeep part number for this differential is 4740833.
View Details
Cases & Spiders
Dana 35 Loaded Open Differential Carrier Jeep 3:54 3:73 4:10 4:56 TJ YJ Wrangler XJ Cherokee
This is a genuine Dana/Spicer loaded open differential carrier for 3:55 and numerically higher (3:73, 4:10, 4:56, etc.). This fits many Jeep applications from the late 1980’s-current production. This carrier comes with the 2 differential side bearings and a set of ring gear bolts.
View Details
This is a genuine Dana/Spicer internal gear kit for the Dana 35 rear differential found in 1993 and newer Jeep applications. The axle gears have a 1.5″ hub where it goes into the carrier.
View Details
Small Parts & Seals
Dana 35 Pinion Seal Jeep Wrangler Rear 1987-2000 Ford Explorer Front
This is a genuine Dana/Spicer pinion seal for the Dana 35 rear axle found in 1987-2000 Jeep’s. These were also used in Ford Explorer front axles.
View Details
This is a set of genuine Dana/Spicer ball joints for 2000 and 2001 Dodge Ram 1500 4X4 trucks with the Dana 44 front end. This is one set for one side and includes 1 upper and 1 lower ball joint, the 2 nuts and 1 cotter pin.
View Details
This is a genuine Dana/Spicer pinion yoke in a 1330 series, for the Dana 44 rear differential found in Jeep TJ Rubicons up to 2006. Can be used on any early model Dana 44 (pre 2006). This is 3/4″ shorter than the factory yoke, but there is usually enough slip in slip yoke to make [...]
View Details
This is a genuine Dana Spicer spindle for the Dana 44 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1973-1976. This is the same as part number 706528X, but it is much cheaper. This also comes with the dust seals, inner bearing, and plastic thrust washer.
View Details
This is a genuine Dana/Spicer 1/2 pipe plug. These were used as differential fill plugs in many Dana differential covers.
View Details
Miscellaneous
Dana 44 60 Dodge 8.25/9.25 Trac Lok Clutch Pack Alignment Clip Posi Track Differential Limited Slip
This is a genuine Dana/Spicer clip that isolates the clutch ears from case in a Trac Lok limited slip differential. These were used in Dana 44’s and Dana 60’s, as well as Dodge 8.25 and 9.25 differentials.
View Details
Axles & Axle Bearings
Dana 44 60 Dodge Disconnect Slide Collar Front Differential Axle 4X4 Ram 1500 2500 3500 Jeep
This genuine Dana slide collar fits most Dodge Dana 44 and 60 front disconnect axles up to 1999. 2000+ Dodge Dana 60’s used a larger splined slide collar which is not available from Dana. This also fit’s many Jeep applications with the disconnect front axle.
View Details
Cases & Spiders
Dana 44 Bare Differential Carrier 3:73 and Lower Numerically GM Chevy Ford Dodge Jeep
This is a genuine Dana/Spicer bare differential carrier for a standard Dana 44. These were used in many domestic applications from the 1970’s to 1990’s, including GM, Chevy, Dodge, Ford, and Jeep. This one is for gear ratio’s 3:73 and down numerically (3:54, 3:31, etc.). This carrier comes with a set of ring gear bolts, [...]
View Details
This is a genuine Dana/Spicer bare differential carrier for a standard Dana 44. These were used in many domestic applications from the 1970’s to 1990’s, including GM, Chevy, Dodge, Ford, and Jeep. This one is for gear ratio’s 3:92 and up numerically (4:10, 4:56, etc.). This carrier comes with a set of ring gear bolts, [...]
View Details