This is a genuine Dana/Spicer coil spring for the factory Spicer lockout hubs found on many late 1960’s to late 1970’s GM and Ford trucks. May be used on other applications as well. This spring is larger on one end than on the other end.
Dana 44 Early 4X4 Front Axle Lockout Hub Conical Coil Spring Original Spicer Lockout Hubs
$24.00
- SKU: 35218
- Brand: Dana/Spicer
- Weight: .30
- Shipping: Calculated at checkout
1 in stock
Weight | .30 lbs |
---|---|
Dimensions | 4 × 4 × 4 in |
Related products
Axles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View DetailsThis is a genuine Dana/Spicer 4X4 front spindle for the Dana 60 front axle found in 1980’s and early 1990’s GM and Dodge trucks. This kit includes inner spindle bearing, thrust washer, and the 2 rubber seals for the backside of the spindle. Photo shows spindle bearing installed, but they usually aren’t.
View DetailsAxles & Axle Bearings
Spindle Nut Washer Rear Hub Dana 60 Spicer Dodge Jeep Ford Lock
This is a genuine Dana/Spicer spindle nut lock washer with folding tabs. These were used in the 1960’s and 1970’s on many common Dana applications, including Dana 60 and 70 front or rear axles. The I.D. is 1 13/16″. The O.D. is 2.375″ and they are 1/16″ thick. These are the same as Dorman part [...]
View DetailsThis is a genuine Dana/Spicer 4X4 front spindle that fit’s the following Ford applications: DANA 44 SPINDLE WITH 5 HOLES. FITS MOST FORD 1977 1/2-1979 F250 . DOES NOT FIT 76-77 LARGE EXTERNAL HUB. BEARING JOURNALS – 2.5″ OUTER & 1.625″ INNER. FLANGE DIA- 6.12″ INNER BRG DIA 2.0” // LENGTH 6.25”
View DetailsMiscellaneous
Dana 60 4X4 Front Axle King Pin Bearing Lower Mount Chevy Ford Dodge GM 4 Bolt Flange Plate
This is a genuine Dana/Spicer lower king pin bearing mount for the Dana 60 4X4 front axle found in many GM, Ford, and Dodge applications. This has a threaded hole in the bottom for a grease zerk, although it is not included. The new Dana part number is 070SC128.
View DetailsThis is a 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View DetailsSmall Parts & Seals
DANA 44 SPINDLE BEARING & SEAL KIT BRONCO F150 1993-1996 FORD 4X4 FRONT AXLE
Dana 44 IFS BRONCO AND F150 1993-1996 Spindle Bearing and Seal Kit Includes 1 each Spindle Bearing (550759 or SCE2110) and V Seal, Wiper Seal (50492), and Thrust Washer (45651) as pictured.
View DetailsThis is a genuine Dana Spicer spindle for the Dana 44 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1973-1976. This is the same as part number 706528X, but it is much cheaper. This also comes with the dust seals, inner bearing, and plastic thrust washer.
View Details