fbpx

Showing 497–512 of 563 results

$4.25

This is a genuine Dana/Spicer axle tube seal for GM applications with the Dana 44 or corporate 10 bolt 4X4 front axle.

View Details
$28.00

This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.

View Details
$19.95

This is a genuine Dana/Spicer greasable universal joint is a 1410 series. This is the same as 5-1410X except it is greasable.

View Details
$325.00

This is a genuine Dana/Spicer internal or spider gear kit for the Dana 30 4X4 front differential found in 2007-2015 Jeep JK’s. This is for the non-Rubicon Jeep’s. 

View Details
$45.00

This is a genuine Dana/Spicer universal joint for the Dana 44 front axle found in many 2007 and newer Jeep Rubicon’s.

View Details
$260.00

This is a genuine Dana/Spicer ring and pinion in a 5:13 ratio, for the Dana 44 rear axle found in most 2018 and newer Jeep JL and JT vehicles.

View Details
$127.50

– 27 spline – 6.11″ long – Fits Dana Spicer 30 in Jeeps – Outer stub – 5-260X U-joint size – Chromoly USED IN 1987 TO 1988 AND 1990-1991 The original part number (40611) has been discontinued.

View Details
$89.95

This is a genuine Dana Spicer bare differential carrier for the Dana 30 4X4 front axle found in many Jeep applications from 1984-2006. This include Wrangler, Cherokee, and Grand Cherokee, XJ, YJ, and TJ. This is for 3:54 and faster gear ratio’s (3:08 etc.).

View Details
$65.00

For Use In 1987-06 Wrangler 1984-01 XJ Cherokee 1986-92 MJ Comanche 1993-98 ZJ Grand Cherokee Dana 30 and Dana 44 4X4 Front Axles This kit will do one side and contains 1 upper and 1 lower.

View Details
$25.00

This is a genuine Dana/Spicer press on axle bearing for the Dana 35 rear axle in some Jeep’s. This is the same as the aftermarket part number A9, except it does not include the press on ring (36121) which we also have available. The number on the bearing is NP182140 and the number on the [...]

View Details
$10.95

This is a genuine Dana/Spicer press on sleeve that goes up against the press on bearing on a Jeep with a Dana 35 rear axle. These were usually found in Grand Cherokee’s. The inside diameter is 1.368″. This goes with bearing number 566075.

View Details
$8.50

This is a genuine Dana rear axle seal for the Dana 35 rear axle in mid 1990’2 to mid 2000’s Jeep Grand Cherokee’s. This is used with the 566075 axle bearing and is the same as National 2146.

View Details
$35.00

This is a genuine Dana/Spicer pinion yoke for the Dana 35 rear differential in most Jeep applications. This is for the 1310 series universal joint. Some of the Jeeps used a 1330, so be sure of your u-joint size before ordering. If you are unsure that this will fit your application, feel free to email [...]

View Details
$240.00

This is a genuine Dana/Spicer posi trac differential for the Dana 44 rear differential found in later Jeep JK applications. This kit includes differential side bearings and 1/2 inch ring gear bolts.  We also have sleeves available to bush the holes down to 7/16 and from 7/16 to 3/8. This is for factory ratio’s from [...]

View Details
$59.95

This is a genuine Dana/Spicer rear axle bearing kit for Dana 44 rear axles with press on bearings. This is a common setup for older Jeeps, Fords, and possibly Internationals. Please be aware that these are larger bearings for the older Dana 44 axles and will not fit the later Super 44 axles. This kit [...]

View Details
$395.00

Brand Spicer Axle Model DANA SUPER 35 Vehicle Location Rear Axle Cover Bolt Hole Quantity 10 Axle Spline Count 27 Differential Case Split 3.54 And Up Differential Type Standard Carrier Description Loaded Axle Spline Diameter (IN) 1.18 Carrier Bearing Included Yes Ring Gear Bolt Hole Qty 8 Ring Gear Bolt Thread Size .437-20 Package Type [...]

View Details