417-862-4455
Miscellaneous
Dana 50, 60, 70, 80 Open Differential Spider Gear Cross Shaft Split Roll Pin GM Ford Dodge
This is a genuine Dana/Spicer roll pin that holds the cross shaft in an open differential. This fits Dana 50,60,70, and 80 differentials. This pin is .225″ diameter and is 1.87″ long. Same as Yukon part number YSPXP-022.
View Details
This is a genuine Dana differential side bearing kit for Dana 60 and 70 (except 70HD). This kit includes 2 387A bearings and 2 382S races.
View Details
Ring & Pinion Sets
This is a genuine Dana ring and pinion set for the front of a Ford truck with Dana 60 3:54 reverse cut. This kit includes all necessary shims, ring gear bolts, pinion nut and washer, and both inner and outer pinion bearings and races.
View Details
Ring & Pinion Sets
Dana 60 3:54 Gear Set Ring & Pinion 354 GM Chevy Ford Dodge Jeep International Standard Rotation
This is a genuine Dana/Spicer ring and pinion for a regular standard rotation Dana 60 axle. This fits most domestic applications for Dana 60 rear axles, and GM and Dodge 4X4 front axle applications. The tooth counts are 46-13. The ring gear number is 32503 and the pinion is a 34023.
View Details
Ring & Pinion Sets
This is a genuine Dana 60 3:54 ring and pinion set for the front or rear in a GM or Dodge application, or the rear of a Ford truck. This is a gear kit that includes both pinion bearings and races, ring gear bolts, pinion seal, pinion nut and washer, and shims.
View Details
Ring & Pinion Sets
This is a genuine Dana 60 3:73 ring and pinion set for the front or rear in a GM or Dodge application, or the rear of a Ford truck. This is a gear kit that includes both pinion bearings and races, ring gear bolts, pinion seal, pinion nut and washer, and pinion shims. This is [...]
View Details
Miscellaneous
Dana 60 30 Spline Axle Drive Flange Cog Gear Slug Fulltime 4X4 Front Hub GM Ford Dodge
This is a genuine Dana/Spicer drive axle flange for a Dana 60 4X4 front axles with the fulltime front end. These were used in GM, Ford, and Dodge applications with the 30 spline outer axle, which is stock for most applications. These have 55 outer splines where it goes into the hub.
View Details
Miscellaneous
Dana 60 35 Spline Axle Drive Flange Cog Gear Slug Fulltime 4X4 Front Hub GM Ford Dodge
This is a genuine Dana/Spicer drive axle flange for a Dana 60 4X4 front axles with the fulltime front end. These were used in GM, Ford, and Dodge applications with the 35 spline outer axle, which wasn’t stock for most applications. These have 55 outer splines where it goes into the hub.
View Details
This is a genuine Dana/Spicer 35 spline axle gear for a Dana 60 or 70 differential with 35 spline axles. These were found in many domestic applications. These are NOS and may have some surface rust, so if you are a whiner or complainer, please move along.
View Details
Transmission Parts
This is a genuine Dana/Spicer Trac Lok differential for a Dana 60 with 35 spline axles. This comes with a set of ring gear bolts, side bearings, and inboard and outboard shims. This fits many application including most 4X4 front axles.
View Details
Traction Devices
Dana 60 35 Spline Trac-Lok Limited Slip Differential GM Ford Dodge
This is a genuine Dana/Spicer Trac-Lok posi for a Dana 60 with 35 spline axles. This includes many GM, Ford, and Dodge 4X4 front axles. The axle gears are machined for c-clips, so they can also be used on semi-float rear axles. These have been discontinued from Dana/Spicer, but we have a few left in [...]
View Details
Ring & Pinion Sets
Dana 60 4:10 Reverse Cut Ford Ring & Pinion Gear Set 4X4 Front F350
This is a genuine Dana 4:10 gearset for a Dana 60 reverse cut in a Ford F350 front axle. This kit includes both pinion bearings and races, crush sleeve, pinion seal, nut, shims, and ring gear bolts. This pinion is made for a crush sleeve rather than preload shims. These were primarily used in 1999 [...]
View Details
This is a genuine Dana 4:10 gearset for a Dana 60 reverse cut in a Ford F350 front axle. This kit includes both pinion bearings and races, pinion seal, nut, shims, and ring gear bolts. This pinion is made for preload shims rather than a crush sleeve.
View Details
Ring & Pinion Sets
This is a genuine Dana 60 4:10 ring and pinion set for the front or rear in a GM or Dodge application, or the rear of a Ford truck. This is a gear kit that includes both pinion bearings and races, ring gear bolts, pinion seal, pinion nut and washer, and shims. If you purchase [...]
View Details
Ring & Pinion Sets
This is a genuine Dana 60 4:88 ring and pinion set for the front or rear in a GM or Dodge application, or the rear of a Ford truck. This gear set uses preload shims instead of a crush sleeve. Tooth counts are 39 on the ring gear and 8 on the pinion.
View Details
Miscellaneous
Dana 60 4X4 Front Axle King Pin Bearing Lower Mount Chevy Ford Dodge GM 4 Bolt Flange Plate
This is a genuine Dana/Spicer lower king pin bearing mount for the Dana 60 4X4 front axle found in many GM, Ford, and Dodge applications. This has a threaded hole in the bottom for a grease zerk, although it is not included. The new Dana part number is 070SC128.
View Details