fbpx

Showing 401–416 of 563 results

$35.00

DUST SHIELD for front BRAKE ROTOR with Dana 60 Front Axle PLEASE NOTE THERE IS ALSO A PART NUMBER 47758 THAT HAS THE SAME BOLT PATTERN, BUT IS ONLY 13 1/4″ DIAMETER. FORD F350 4×4 with DUAL rear wheels 2000-1/2 F450, F550 4×4 with DUAL rear wheels 2000, 2001, 2002, 2004 DOES NOT FIT 2005 and [...]

View Details
$395.00

This is a genuine Dana Trac-Loc differential for Dodge vehicles with the 8.25″ ring gear from 1976-1996 with 27 spline axles. This is what came out in these year vehicles from the factory if they had a posi track differential. They also make a nice upgrade when replacing an open differential. The old Dana number [...]

View Details
$360.00

This is a genuine Dana Trac-Loc differential for Dodge and Jeep vehicles with the 8.25″ ring gear from 1997+ with 29 spline axles. This is what came out in these year vehicles from the factory if they had a posi track differential. They also make a nice upgrade when replacing an open differential. The new [...]

View Details
$425.00

This is a genuine Dana Trac-Loc differential for Dodge vehicles with the 9.25″ ring gear from 1970-2009 with 31 spline axles. This is what came out in these year vehicles from the factory if they had a posi track differential. They also make a nice upgrade when replacing an open differential. The new Dana number [...]

View Details
$2.55

This is the outer axle nut washer that goes with the 46085 axle nut on 4X4 Dodge front axles, this fits Dana 44 and 60 as well as the AAM 9.25 front axle found in 2003 and newer Dodge Ram 2500 and 3500 series trucks. 

View Details
$7.00

This genuine Dana axle nut fits all Dodge front axles including Dana 44 & 60 and the AAM 9.25 found in 2003+ trucks. This is a castle nut. We also have the washer available. This is the same part as AAM 40010627.

View Details
$105.00

This genuine Dana front outer stub axle fits Dodge 1/2 ton trucks from 1994-2001 with the Dana 44 front axle. this axle is 6.77 long from the center of the u-joint to the tip of the splines and is 1.41 33 spline. If you are not sure of this part number you can call or [...]

View Details
$195.00

This is a genuine Dana intermediate axle for a Dana 60 with a disconnect axle in a Dodge 3/4 or 1 ton truck from 2000-2002. This axle is set up for a larger slide collar than the earlier models. This axle runs from the slide collar out to the u-joint.

View Details
$145.00

This is a genuine Dana right hand inner axle for the disconnect side of a Dodge 3/4 or 1 ton truck. This is the one that runs from the differential to the discconnect on the passenger side front axle. this fits trucks from 1994-1999. If you are unsure of the part number you can call [...]

View Details
$105.00

This is a genuine Dana right hand inner axle for the disconnect side of a Dodge 3/4 or 1 ton truck. This is the one that runs from the differential to the discconnect on the passenger side front axle. this fits trucks from 2000-2002. This one has larger splines where the slide collar splines on [...]

View Details
$105.00

This is a genuine Dana front outer stub axle that fits 3/4 and 1 ton Dodge trucks from 1994-1999. It is 7.05″ long.

View Details
$160.00

These are genuine Dana outer stub axles that show to fit 2000-2002 Dodge 3/4 and 1 ton trucks with the Dana 60 front differentials. These are 1.41 33 spline and 7.39 from the center of the u-joint to the tip of the threads. If you aren’t sure about the part number for you application you [...]

View Details
$14.95

This is a genuine Dana/Spicer rear wheel hub seal that fits most Dodge Ram trucks with the Dana 80 rear differential. This is the same as a National 455086 and the seal in the package is an SKF with a part number 30033. As always if you are unsure of the part number you need, [...]

View Details
$6.00

This is a genuine Dana/Spicer nylon axle support bushing. This goes in the middle axle and rides on the pilot of the inner axle. The were used in Jeep and Dodge applications with the disconnect 4X4 front axle.

View Details
$21.00

This is a genuine Dana/Spicer u-joint strap kit for the 7290 series joint found in many Mopar applications.

View Details
$29.95

This is a genuine Dana/Spicer axle support bearing for the Dana 44 and Dana 60 4X4 front axles used in 1994-1998 Dodge Ram 1500 2500 and 3500 series trucks. The bearing has a number SCE228 on it.

View Details