417-862-4455No products in the cart.
$0.75
This is the gasket for the 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s.
View Details
Out of stock
$12.00
This is a 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details
$3.50
This is the upper nylon bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to mid 1990’s.
View Details
$13.75
This is the upper screw in pin a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details
$1.85
This is a spring seat that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View Details
$45.00
This is a lower king pin bearing and seal kit for a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s. This kit does one side. 2 kits required per truck.
View Details
$3.75
This is a tin cap that covers the lower bearing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s.
View Details
Individual Bearings
Dana 60 King Pin Lower Bearing Kit GM Chevy Ford Dodge 4X4 Front Axle
$93.00
This is a lower bearing kit for a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s. The bearing number is 23100 and the race is 23256. These are Timken Bearings. One kit will do both [...]
View Details
Out of stock
$195.00
This is a master king pin kit for the Dana 60 front ends from the early 1970’s to the mid 1990’s. These fit most domestic applicarions. Included parts are as follows: 2 706395X (lower kit) 2 620132 (Upper 4 bolt cap) 2 37307 (upper 4 bolt gasket) 2 620180 (upper spring seat) 2 41886 (upper [...]
View Details
$0.75
This is a genuine Dana/Spicer main cap bolt for Dana 60, 70, and 80 applications.
View Details
$7.00
This is a genuine Dana/Spicer spindle nut that fits some early model Dana 60 rear axles. This nut has a 2 3/8″ hex on the outside and is 1 13/16″-16TPI on the inside. This is the same as a Dorman part number 615-131.
View Details
$40.00
This is a complete set of aftermarket spindle nuts and washers for a Dana 60 front axle. It consists of 2 each inner nut with pin, locking washer, and outer nut with the pin. These were commonly found on GM, Ford, and Dodge applications. They were also used on Dana 50 applications in Ford applications. [...]
View Details
Miscellaneous
$45.00
This is a genuine Dana tone ring for a Dana 60 rear differential. This works on both Ford and Dodge applications.
View Details
Cases & Spiders
$75.00
This is a genuine Dana clutch pack for a Dana 60 Trac Lok differential. This kit includes enough clutches to do both sides.
View Details
Cases & Spiders
Dana 70 80 Power Lok Internal Axle Gear Kit 32 Spline Dodge Posi Limited Slip Differential Posi Lock
$650.00
This is a genuine Dana internal kit with clutch pack for a Dana 70 Power Lok with 32 spline axle gears. These were usually found in Dodge 2500 and 3500 series trucks from 1991-2002, but also found in some Fords of similar years. If you are unsure of your application feel free to email with [...]
View Details
Miscellaneous
Dana 70 80 Rear Hub Nut Nylon Lock 2″ 16 TPI 2 9/16″ Socket Full Float Dodge, Ford, GM
$24.00
This is an aftermarket rear hub nut for use on Dana 70 and 80 rear axles with 2″ 16 threads per inch. This is the style that uses a wedge key that drives in a keyway on the top of the spindle and cuts through the nylon part of this nut. This nut is right [...]
View Details